- “Water covering the filter at the end of a cycle”
- “A cycle that stops part-way”
- “A code that returns as soon as it fills”
Symptom
Bertazzoni dishwasher not draining
Water standing over the filter plate at the end of a cycle, or a machine that stops part-way. These dishwashers publish real codes — the only appliance in the line that does — and the answer is very often something you can see with the filter in your hand.
- From $95 diagnostic, credited to the repair
- 59 cities and neighborhoods covered
- OEM parts available on order
- In writing the price, before anything is opened
Five ordinary causes
What this usually turns out to be
Cheapest and commonest first, which is also the order we check them in. They sit hundreds of dollars apart, and only the unit settles which one is yours.
-
The filter and the sump
Visible with the filter in your hand, free to clear, and the answer often enough that it is worth doing before you call.
Dishwasher drain & filter repair from $145 -
The drain hose
Crushed behind a bin under the sink, kinked, or without the high loop that stops the sink draining back into the machine.
Dishwasher drain & filter repair from $145 -
A disposal knockout plug never removed
A classic, and entirely outside the appliance. If a garbage disposal was fitted after the dishwasher, this is worth checking first.
Dishwasher drain & filter repair from $145 -
The drain pump
Real, and last — because a pump replaced with a blocked hose still attached is a repeat visit rather than a repair.
Dishwasher drain & filter repair from $145 -
The control not commanding the drain
Rare, and only after the path is proven clear. The code usually distinguishes this from a blockage.
Dishwasher control & electronics repair from $215
In five minutes
Before you call anybody
None of it needs tools, and all of it makes the visit shorter.
-
01
Record the code first
Clearing it destroys the one piece of evidence the machine gave you.
-
02
Filter out, sump inspected
Five minutes, no tools, and sometimes the whole answer.
-
03
Look under the sink
Hose crushed, hose kinked, high loop gone, disposal plug still in.
-
04
Does the sink drain normally
A blocked kitchen drain will stop a dishwasher and has nothing to do with it.
How it shows up
What people describe when they call
A shortcut
Narrow it down before anybody arrives
A description of the behaviour leaves a few possible causes. A code names the subsystem before anybody opens anything, which is why it is worth photographing before it clears.
If the display is showing something
- F5 Pressure system failure — the machine can no
- F8 Heater error — the heating element or its
- HI High voltage failure. This one is about the
- FF The machine did not get the water it
- F2 The machine could not discharge its water. The
Photograph it before it clears — codes do not wait. Search the full code list
In more detail
About Bertazzoni dishwasher not draining
The fastest diagnosis is the code
Write the code down before you clear it, then lift the filter out, rinse it and look in the sump underneath. Glass, a fruit sticker or a bone chip is what actually blocks these. Then look under the sink: a drain hose crushed behind a bin, or a garbage disposal fitted without its knockout plug removed, produces this exact symptom and is not the dishwasher at all.
The one machine here with a code table
Almost nothing else this maker builds reports an error. Its dishwashers do, and that makes them the most diagnosable appliance on this site. Record the code exactly, including the letter, and note whether it survives a power cycle at the breaker. It is worth more than any description.
Outside in, not inside out
Filter, sump, hose, disposal, then pump. That order is deliberate: a drain pump is a part and a fitting charge, a knockout plug is two minutes, and they present identically. Working from the outside in is what keeps the second from being billed as the first.
This article is based on:
- Official manufacturer documentation
- Internal repair procedures
- Technician repair history
- Company quality standards
Before you book
Questions about bertazzoni dishwasher not draining
How much water in the bottom is normal?
A small amount in the sump is normal and by design — it keeps the seal wet. A pool covering the filter plate is not. The filter plate is the line: water above it at the end of a cycle wants looking at.
The code came back straight away after I cleared it.
That is useful and worth telling us. A code that stays away for days is a different situation from one that returns on the next fill — the second means the machine is detecting the same condition immediately, which points at the drain path rather than at an intermittent sensor.
It drains but slowly.
Usually a partial restriction rather than a failed pump: a filter that has not been out in a year, a hose with build-up, or a high loop that has slipped. Slow draining is the cheap stage of the problem that later presents as no draining at all, and it is worth reporting then.
Where we do it
Across Miami-Dade, Broward, and Palm Beach
Same terms everywhere we go: an on-site diagnostic first, the price agreed in writing, and the exact figure confirmed once we have seen the unit.
Neighborhoods people ask for by name